· Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions. Aggregate crushing value is a numerical index of the strength of the aggregate and it is used in construction of roads and pavements.

· The ‘ aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load.

The average crushing value in the different tests is the actual crushing value of aggregate. Important points to remember It is recommended that the crushing value of aggregate should be less than 30%. If it is more than 30 % then 10% finer aggregate is suggested to use.

Aggregate Crushing Value Test is important to test to be performed on aggregate. The strength of aggregate parent rock is determined by preparing a cylindrical shape specimens of size 25 mm diameter and 25 mm height. This cylinder is subjected to compressive stress.

Significance of Aggregate Crushing Value Test The crushing value test is conducted on aggregates that are used for the construction of roads. Lower crushing value aggregates give much more durability for roads due to its lower crushed fraction under the compression load. The road is subjected to motion pressure continuously.

· The crushing value of an aggregate indicates its resistance against crushing under gradually applied compressive loads. The standard aggregate crushing test is made on aggregate passing 12.5mm IS sieve and retained on 10 mm IS sieve.

The aggregate crushing value is a numerical index of the resistance of an aggregate to crushing under a gradually applied compressive load. It is expressed as the percentage by mass of the crushed (or finer) material obtained when the test sample is subjected to a …

Academia.edu is a platform for academics to share research papers.

Definition The aggregate crushing value (ACV) of an aggregate is the mass of material, expressed as a percentage of the test sample. which is crushed finer than a 2,36 mm sieve when a sample of aggregate passing the 13,2 mm and retained on the 9,50 mm sieve is subjected to crushing under a gradually applied compressive load of 400 kN. 2 APPARATUS

Calculation of Aggregate Crushing Value. The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the IS sieve 2.36mm and the weight of the dried aggregate sample. At least three samples should be tested from the same batch and average value to get accurate results.

AGGREGATE CRUSHING VALUE 1.Objective The aggregate crushing value gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggregate of aggregate crushing value 30 or higher, the result may be anomalous, and in such cases the ten percent fines value should be determined instead.

Aggregate Crushing Value Test Determine Aggregate. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under standardized conditions, and the strength of the aggregate used in road construction is expressed by numerical index.

· The crushing value of an aggregate indicates its resistance against crushing under gradually applied compressive loads. The standard aggregate crushing test is made on aggregate passing 12.5mm IS sieve and retained on 10 mm IS sieve. Procedure. About 6.5 Kg material consisting of aggregates passing 12.5mm IS sieve and retained on 10mm sieve is .

· AGGREGATE CRUSHING STRENGTH TEST Theory and Scope: This is one of the major Mechanical properties required in a road stone. The test evaluates the ability of the Aggregates used in road construction to withstand the stresses induced by moving vehicles in the form of crushing.

To calculate aggregate Crushing value by testing aggregate passing 12.5 mm sieve and retained on a 10 mm sieve. Scope: This procedure covers all relative activity for the project site. . This is known as aggregate impact value test IS 283-1970.

The aggregate crushing value (ACV) provides relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Two versions available: 150 (standard) and 75 mm dia. The apparatus comprehend cylinder, plunger, base plate, tamping rod and measure.

The apparatus of the aggregate crushing value test as per IS: 2386 (Part IV) – 1963 consists of: 1) A 15cm diameter open ended steel cylinder with plunger and base plate, of the general form and dimensions as shown in Fig 1. 2) A straight metal tamping rod …

· Objective For determination of the aggregate crushing value of coarse aggregate, which passes 12.5 mm. IS sieve and retained on 10 mm. IS sieve. Reference Standard IS: 2386 (Part IV)-1963 Methods of test for aggregate for concrete Part IV Mechanical Properties. Equipment & Apparatus Steel Cylinder Sieves (12.5mm,10mm) Cylindrical metal measure Tamping Rod Balance (0 …

Los Angeles abrasion test on aggregates is the measure of aggregate toughness and abrasion resistance such as crushing, degradation and disintegration. This test is carried out by AASHTO T 96 or ASTM C 131: Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine. The aggregate used in surface course […]

The test aims at looking for the forces required to produce 10% of fine values (i.e. weight of fines aggregates/weight of all aggregates = 10%). This test is very similar to Aggregate Crushing Test in which a standard force 400kN is applied and fines material expressed as a percentage of the original mass is the aggregate crushing value.

The Aggregate Crushing Value (ACV) Test Set provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Each set consists of steel cylinder, plunger, base plate, cylindrical measure and tamping rod. All parts of the apparatus are powder coated or galvanized steel, heat treated and ground .

Calculation of aggregate crushing value. The aggregate crushing value is defined as the ratio of the weight of fines passing through specified IS (here 2.36mm sieve) to the total weight of sample expressed in percentage. W1= Weigh of the total aggregates (Wa-We) W2= Weigh of aggregates passing through 2.36mm IS sieve.

· The aggregate crushing value test evaluates the ability of the aggregates used in road or pavement construction to withstand the stresses induced by moving vehicles in the form of crushing. With this, the aggregates should also provide sufficient resistance to crushing under the roller during construction work and under rigid tyre rims of .

For any questions, you can send us a message by completing the form below.